手机赌博直营首页

Thermal oil heater
Thermal oil heater
Mold temperature machine
Electric heating oil furnace
Oil temperature machine
Oil heater
Water circulation temperature control machine
Chiller
Hot and cold machine
Thermal oil heater

Your present location: Home > Products > Heat Conductor Oil Heater

Thermal oil heating system


The main effect of the first heating of the heat transfer oil heating system is to control the temperature to keep the temperature stable. In the process of use, there is residual water in the pipeline or water in the heat transfer oil component, which causes oil and water to mix. At high temperatures, water vaporization causes system pressure to change Stability, will lead to oil spill in the fuel tank. Water can be removed by dehydration and cooking oil. How to operate it?


Judgment and analysis of oil-water mixture in heat transfer oil heating system :

The system pressure is normal at normal temperature. When the temperature rises (above 80 degrees), the system pressure gauge will shake up and down. There is a lot of white smoke in the fuel tank or the liquid level switch of the heat-conducting oil system to determine the oil-water mixture.

Dehydrated cooking oil method:

Remove the upper cover of the machine and open the fuel tank cover. Set the temperature to about 80 degrees first, and then combine with the system pressure gauge. When the system pressure is stable, increase it again by two degrees. If the system pressure drops again at this time, you should immediately lower the temperature again and wait for the pressure. After stabilization, increase it again twice.

The heat transfer oil heating system uses this method to finally control the oil temperature to about 130 degrees when the pressure is stable, and let it run for 1-2 hours to dehydrate the oil. After the system pressure is completely stable, you can heat up and observe the system pressure again. No change.


When purchasing the heat transfer oil heating system , it is necessary to consider the production needs and information process parameters in detail, and to make a proper decision in accordance with the strict verification of the capabilities of the heat transfer oil heating system. The main purpose of any heat transfer oil heating system is to control the equipment temperature within the range of (± 2 ° F). Therefore, the temperature control of the liquid running between the pipes must be precise, otherwise the purpose of temperature control cannot be achieved. The above is a brief analysis on how the dehydration cooking oil of the heat transfer oil heating system is carried out.


Selection of important parameters for heat transfer oil heating system selection:

model

Unit Unit

JEOT-10

JEOT-30

JEOT-50

JE0T-75

JEOT-100

Temperature control range

         Room temperature -300 ℃

Temperature control accuracy

±1 PID ± 1

power supply

380V50HZ3P AC3 380V50HZ3P

Heat transfer media

          Oil Thermal oil Oil

  cooling method

         lndirect Cooling Indirect cooling

Expansion tank capacity

L

twenty four

28

55

100

150

Heating energy

KW

18

24/36

40/60

50/75

80/100

Pump power

KW

0.75

2.2

3.75

5.5

7.5

Pump working flow

3 /H M 3 / H

1.5

10

16

18

25

Pump working pressure

KG / CM2

2.2

2.8

3.2

4.0

5.0

power consumption

KW

20

40

65

85

110

Alarm function

Phase loss / oil shortage / overtemperature / overload / oil spill / heating abnormal alarm /

Cooling water piping

INCH

1/2

1/2

1/2

1/2

3/4

Circulating oil piping

INCH

3/4

1

1-1 / 4

1-1 / 2

2

Dimensions

MM

×500×1000 1150 × 500 × 1000

×580×1250 1450 × 580 × 1250

×550×1200 1600 × 550 × 1200

×550×1200 1600 × 550 × 1200

×600×1400 1600 × 600 × 1400









 


Previous: Conductive oil heater

Next: No more!

online service

Online Contact
点击这里给我发消息
金牛彩票手机官网 可以赌钱的棋牌游戏 快发彩票娱乐手机官网 vr真人彩网娱乐平台网址 糖果派对电子游艺下载 博牛1分钟快3彩票平台 全民牛牛官网 本溪棋牌网官方下载 pc福利群 龙虎和最新微信群号